Control Electronics model CPS-460DH Ultrasonic Doppler Flowmeter is a non-contacting, non-intrusive system that continuously monitors the flow in full pipes with at least 70 ppm suspended solids or air bubbles, indicating flow rate, totalized flow and many other variables. The system has 2 independent 4-20 mA analog outputs, 4 control relays and 1 sampler pulse relay, all programmable. The sensors may be mounted on any pipe size from 1.0” to 50”. A 200 day time stamped data logging provides 24 hour summary of flow rate, total flow for day, number of pump cycles with run time and more.
The US460DH Sensor is a dual-head arrangement with 25 feet of coaxial cable. The PVC sensors are easily mounted to the outside of the pipe using the supplied Silicone grease ( coupling paste ) and stainless steel hose clamp.
Typical sensor mounting
The Model CPS-460R allows for remote monitoring of up to 1000 feet using an inexpensive two twisted pair shielded interconnect cable. The Ultrasonic transmit and receiver card is located at the measuring site in a NEMA 4X enclosure.
Variables Displayed On Backlit Digital LCD Display
( User Selectable )
1] GPM / Totalizer 2] MGD / Totalizer 3] Velocity in FPS / GPM
4] Measured Average Frequency / Noise Filter Setting
5] Flow % / Signal Strength
6] LPM / Total liters 7] Cm/h / Total Liters 8] Velocity m/s / LPM 9] Velocity m/s / Cm/h;
For Programming Meter, RESETing Meter and Trouble Shooting go to SUPPORT.
Power: 120/220 VAC, ±15%, 50/60 Hz @ 15 watts max.
Temperature: 30°F to 120°F
Display: 2 x 20 character, alphanumeric LCD with LED backlight
Totalizer: 8 digit accumulative with programmable multiplier;
x1, x10, x100, x1000
Outputs: Two independent 4-20 mA isolated into 1000 ohm load
each, ±1.0% of full scale.
RS-232 terminal ( USB with adapter ), RJ-11 modular jack,
4 alarm control relays and 1 Sample Pulse relay, all
programmable. Relay contacts SPDT 5A/250 VAC
Flow Range*: 0.5 to 25.0 feet per second (FPS)
Sensitivity**: Minimum 70 ppm suspended solids and/or entrained gas
or air bubbles
Resolution: 0.01 FPS, 0.01 GPM
Accuracy***: ± 0.5% of received signal
Memory: Flash and non-volatile RAM ( 3 V battery backup )
Data Log: 200 day flow summary of date, daily avg. GPM, Total
pump run time, Total pump cycles, total gallons pumped
Time Stamped avg. GPM flow rate with programmable log
rate of 00-99 minutes
EVENT list time stamped ( view by down load only ) using
any standard communication software
* Flow velocities of approximately less than 1.0 FPS (±0.5) not
recommended ( This is transition from turbulent to laminar flow -
calibrations different )
** Application dependent - velocity / pipe may necessitate higher ppm
*** Received signal is application dependent. Field / application conditions
may affect apparent accuracy
Note: CPS-460DX system does not come with relay outputs or data logging
CPS-460DH / 460DX Doppler Flowmeter Specifications 8/20
Material: PVC Housing, Epoxy
Fréquence.: 640 kHz.
Temperature: -40°F to 160°F exposure
Cable: 25 foot corrosion resistant coax, 50 feet max.
Dimensions: 1.5”W x 2.0”L x 1.0”H ( sensor heads only )
Mounting: Recommend stainless steel hose clamp with silicone grease
Rating: Sensor is explosion proof, corrosion resistant, immersible
Type Pipes: Steel, PVC, Cast Iron, Most FRP and some lined pipes
Material: Fiberglass with clear hinged Polycarbonate cover, stainless steel hinges
and mounting hardware
Rating: NEMA 4X, IP65, Dust-Tight, Water-Tight, Corrosion Resistant, CSA / UL
Dimensions: 7.2” x 11.8” x 6.8”
Mounting: 4.92” x 12.3”
Additional Manuals; 120 VAC, 6 foot power cord installed; additional 4 oz. tube Silicone grease
The CPS-460DH and 460DX units are pretested and inspected before shipping. Warranty is against defects in parts and workmanship for a period of one (1) year from ship date.
Specifications and Design are subject to change without notice.
These specifications supersede all other published specifications.
Made in USA
© Control Electronics Inc., 2020
Designing / Manufacturing Since 1980